This is a two-way driver to control the Symetrix Jupiter 4 DSP.
|
|
| Manufacturer |
Symetrix |
| Model |
Jupiter 4 |
| Jupiter App |
Gain-sharing Automixer #1 (#5 is control-identical) |
| Driver Name |
Symetrix Jupiter 4 |
| Driver Version |
26.08.12.02 |
| Document / Driver Revision |
Aug 12, 2026 |
| Control |
UDP, port 48630 |
Full two-way control of a Jupiter 4 running the Gain-sharing Automixer app: the four output zones, the 4-channel gain-sharing auto mixer, and both matrix submixes each with real-time feedback over the Jupiter push protocol, so panels follow changes made from Symetrix Composer, ARC wall panels, or other touchpanels instantly.
Jupiter apps use fixed controller numbers, so the driver is matched to the Gain-sharing Automixer #1 app (Automixer #5 uses the same numbers). Other Jupiter apps use different controller tables and are not supported by this driver.
- 4 output zones volume and mute on Outputs 1-4, using ELAN's native zone controls
- Gain-sharing Auto Mixer channel gain faders 1-4 with dB readouts, channel mutes, master fader and master mute
- Two submixes (Submix 1 and Submix 2 as ELAN sources) six send faders each (Channels 1-4, Stereo 1/2, Stereo 3/4) with dB readouts, plus master fader and master mute per submix
- Channel on/off buttons and channel-pair lock for the auto mixer
- Presets 1-10 recall
- Noise generator white / pink / sine with level and sine-frequency sliders
- Logic outputs 1-4
- Real-time push feedback (PU/PUE) with full state sync on every connect and a 10-minute push-health check
- 90-day trial, then Innovo MAC-based activation
- Load the Gain-sharing Automixer #1 (or #5) app onto the Jupiter 4 from the Symetrix Jupiter software and configure/test the audio there first.
- Assign a static IP address (or DHCP reservation) to the Jupiter the driver targets it over UDP port 48630.
Controller numbers are fixed per Jupiter app. To confirm which app is loaded, open the Jupiter software's app-selection screen; View External Controllers shows the table this driver was built against.
- Open Media, add a new Audio Zone Controller, and import the Symetrix Jupiter 4 driver.
- If you receive a warning that this is not a Native ELAN driver, click OK.
- The driver automatically enters Trial Mode for 90 days. Wait about 10 seconds and the Status turns Green.
- Add the Innovo Activation Code received in the email.
- Enter the Jupiter's IP address. On connect the driver reads back every fader and mute, then enables push feedback.
- Zones 1-4 map to the Jupiter's Outputs 1-4 bind them to rooms as usual.
- Two sources appear: Submix 1 and Submix 2. Both share the same mixer page; the sliders automatically control whichever submix's source tab is selected.
- Zone volume / mute operate the Jupiter output faders and mutes directly from any zone UI.
- The mixer page shows the auto mixer section (channel faders, channel mutes, master) plus the selected submix's six send faders and its master fader/mute. Every fader has a live dB readout; "Off" means the fader is at minimum (-72 dB).
- The Input 1-4 buttons toggle an auto-mixer channel on/off (a channel reads "on" whenever its fader is above minimum).
- Presets load device-wide from the zone options; the driver confirms the load and refreshes push feedback afterwards.
- All feedback is bidirectional changes made in Symetrix Composer or from ARC wall panels appear on the ELAN panels in real time.
- Buttons/sliders do nothing on the device check the IP address and that UDP port 48630 is reachable (no VLAN/firewall block between controller and DSP).
- Wrong things move on the device a different Jupiter app is loaded. This driver requires Gain-sharing Automixer #1 or #5; verify via View External Controllers in the Jupiter software.
- Panel doesn't follow external changes push is (re)enabled on every connect and checked every 10 minutes; power-cycling the driver connection (re-Apply the IP) forces a full re-sync.
- Preset selection snaps back the device rejected the preset load; the driver re-reads the last loaded preset from the DSP.
- Full control surface for the Gain-sharing Automixer app: 4 output zones, auto-mixer channel/master faders and mutes, and both matrix submixes (6 sends + master each) as per-source ELAN tabs.
- Controller map taken from the app's own External Controllers table (shipped with the driver as reference).
- Real-time push feedback with full sync on connect; dB readouts on all faders.
- Removed legacy controls carried over from other Symetrix apps.
- First release of the restructured driver: 4 zones on Outputs 1-4, auto mixer with proper faders, Submix 1 master controls.