¶ Integration Note
| Manufacturer: | Lexicon |
| Model Number(s): | RV-6, RV-9, MC-10 |
| Driver Name | Lexicon |
| Driver Version | 24.06.10.00 |
| g! Core Module Version: | 8.5 Build 18 |
| Driver Developer: | Innovo |
| Document Revision Date: | June 10, 2024 |
¶ Overview
This is an IP two driver to control Lexicon Receivers and Audio Processors
The Elan controller is capable of controlling the devices, switching sources, adjusting volume, adjusting audio settings, FM tuning, Preset tuning, DAB Scan, FM feedback and two-way feedback for Zone 1 and Zone 2. The driver will also listen for any manual changes made to the receiver outside of Elan and report those to the driver.
¶ Supported Features
THE FOLLOWING OPTIONS ARE SUPPORTED :
- This Driver supports up to 14 sources on the receiver/processor. Please hide any sources not available on the receiver.
THE FOLLOWING PLAYBACK OPTIONS are not supported:
Support for DAB is limited to scan and station feedback.
Any feature not specifically noted as supported should be assumed to be unsupported.
¶ Device Configuration
- The driver uses IP-based communication. Communication must be enabled on the receiver to allow Elan to control the device.
- The AV must be correctly configured for Control; by default, Control is disabled for minimum standby power consumption. IP can be enabled using the OSD menu. Use the remote control press on Menu in order to access the setup menu. Enter the General Setup menu and locate the option Control. Change this parameter to ‘On’. IP control is via port 50000 of the IP address of the unit (in the Network Settings menu). Restart the Unit.
¶ Driver Configuration
¶ Installation Process
IMPORTANT NOTE:
It is recommended that you follow the below installation process in order to ensure you are running the latest version of the [driver].
- Open Media, Zone Controllers, Add New Zone Controller
- Navigate to the folder where the driver is located and Choose the Lexicon AVR
- You’ll receive a warning that this is not a Native Elan driver, click OK
- The Driver will automatically go into trial mode for 30 days. Wait for about 10 seconds and the Status will turn Green. Fill in the IP address and the activation and click Apply.
- Set up sources and hide any unnecessary zones not supported by the receiver model.
- YOU ARE NOW READY TO USE THE DRIVER.
¶ Configuration Details
The following table provides settings used in Configurator …Please refer to the Configurator Reference Guide for more details.
In the table below:
- “<User Defined>”, etc. Type in the desired name for the item.
- “<Auto Detect>”, etc. The system will auto detect this variable.
| Devices | Variable Name | Settings | Comments |
| Media | Name | User Defined (Default: Lexicon AVR) | |
| System # | <Auto Detect> | ||
| Device Type | Ethernet | ||
| Driver Name | Lexicon | ||
| Driver Version | <Auto Detect> | ||
| Driver Vendor | Innovo | ||
| Activation KEY | <User Defined> | ||
| IP Address | <User Defined> | ||
| Zone Controller | Display Name | <User Defined> (Default: Lexicon) | |
| System # | <Auto Detect> | ||
| Source Device | <User Defined> (Default: Lexicon) |
¶ Using the Driver
To use the driver, select a source
- To use the FM, an automatic Interface is installed and setup for use. The interface emulates the physical remote of Lexicon and is mapped to the HR series remotes by Elan.
NOTE: The Station, Genre and Playback Information doesn’t always populate. This is directly read from the information provided by the station itself. The Preset Keys will not populate until the stations are added to favorites in the AV receiver first.
- To Recall A favorite using the the Favorite Previous / Next, Click Ok after the favorite is reached.
- To Set a favorite, follow the instructions on the screen and use the yellow button to confirm.
- Change the audio settings directly in the Settings Page of the Zone.
- Surround mode is a cycle button and emulates the IR remote control. The first push wakes up the receiver for surround mode, the second push cycles through the available Surround Modes. The second push must be within 2 seconds of the first push, other the procedure must be repeated.
- If Direct Mode is on, Surround Mode is not available.
- Zone 2 has a reduced set of adjustments.
¶ Troubleshooting
- Driver not Activated. Wait 15 seconds after Apply